Wiper Linkage Replacement

Mobile wiper linkage replacement at your home or office, for wipers that move unevenly, stop overlapping or have one arm dead.

Book Your
Car Service

icon-whatsapp

Pricing

Pricing varies based on your vehicle

Get a Quote

Service Info

Typical Duration 1.5 hours

We confirm the linkage rather than the motor is at fault, remove the wiper arms and scuttle panel, replace the linkage assembly, clear the scuttle drains, then refit the arms to their marked positions and verify the sweep pattern and park position.

Skip the garage, our master mechanics come to you

At your home or office
Fair & transparent pricing
6-month, 6000km warranty

The Most Trusted Mobile Wiper Linkage Replacement

The wiper linkage is the set of rods and ball joints that converts the wiper motor rotation into the sweeping movement of both arms. It sits in the scuttle under the windscreen, where water and grit collect, so the joints wear and eventually pop apart. The classic sign is one wiper still working while the other sits motionless. Michanic replaces wiper linkages at your home or office, along with the drains that caused the wear.

Why Choose Our Mobile Wiper Linkage Replacement Services?

  1. One Arm Dead Diagnosed:
    A single wiper that has stopped while the other works is nearly always a linkage ball joint that has separated, not a motor fault.
  2. Motor Protected:
    A stiff linkage is what burns out wiper motors. Replacing it before the motor fails is the cheaper order of events.
  3. Drains Cleared:
    Blocked scuttle drains keep the linkage sitting in water, which is why it corroded. Clearing them is part of the job.
  4. At Your Home or Office:
    Wipers that have stopped working properly make the car unsafe in rain, so we come to you.

Why We are the Best Choice for Mobile Wiper Linkage Replacement

  • Complete Assembly Fitted:
    Worn ball joints cannot be reliably repaired individually. The linkage is replaced as an assembly so the geometry is correct.
  • Arm Positions Marked:
    Positions are marked before removal so the blades park exactly where they should and sweep the full screen.
  • Motor Assessed:
    A motor that has been fighting a seized linkage may be close to failure. We tell you if it is drawing excessive current.
  • Sweep Pattern Verified:
    Both arms are checked through their full sweep to confirm they do not overlap or strike the pillars.

A linkage that has separated leaves one wiper stationary, and on the driver side that removes the swept area directly in front of you. The failure is also progressive in a way that costs more if ignored: as joints develop play, the motor works harder and the arms flutter at speed, and a partially detached rod can foul the bonnet or windscreen surround. The underlying cause is almost always water, because blocked scuttle drains leave the mechanism permanently wet, which is why clearing them matters as much as the new parts.

Frequently Asked Questions

  • Why has one of my wipers stopped working?
    Almost always a linkage ball joint that has worn and popped off its pin. The motor and the other wiper continue to function normally, which is exactly what distinguishes a linkage failure from a motor failure.
  • Can a wiper linkage be repaired instead of replaced?
    Individual joints can occasionally be re-secured as a temporary measure, but the plastic bushes wear as a set and the repair rarely holds. Replacing the assembly restores the correct geometry and is the durable answer.
  • Will a worn linkage damage the wiper motor?
    It can. A stiff or corroded linkage makes the motor draw much higher current, which overheats it and shortens its life considerably. Replacing a worn linkage early often saves the motor.
  • Why did my wiper linkage wear out?
    Water. The linkage sits in the scuttle, and when the drains block it sits in standing water, which corrodes the rods and washes grease out of the joints. That is why the drains are cleared as part of the repair.
  • Why do my wipers now hit each other?
    Play in worn linkage joints changes the timing between the two arms, so their sweeps begin to overlap. It needs attention quickly, because wipers that lock together stall the motor and can bend the arms.